Categories rehetra




How to carry out the wall operation of the plastic floor

Views:76 Mpanoratra: Site Editor Fotoana famoahana: 2021-03-11 Origin: Site

The wall on the plastic floor (wall skirt) can decorate the wall, protect the wall, etc. The wall on the plastic floor is also a decorative design of the visual space, and the overall installation effect is perfect. So what are the processes when installing PVC plastic floor? Next, let Jinsheng introduce to you how to carry out the wall operation of the plastic floor.

1. First, the basic treatment of the upper wall

1. The base layer of the wall surface should be flat, dry, strong, free of grease, sand, no shells, no pitted surface, no cracks, no dirt, etc. (Do not scratch the walls such as putty, white cement and white latex paint. The walls should be leveled with cement to increase the surface strength and facilitate bonding)

2. Before installing the wall, the undulating wall must be polished with a sander or sandpaper to improve the flatness of the pasted surface. The polished wall must be completely vacuumed with a vacuum cleaner, and the wall must be cleaned. Tiny particles.

3. The wall texture of the interior wall paint is soft and directly pasted, which is easy to cause peeling. In order to improve construction efficiency and save construction costs, plastic floor edge holders and upper wall lining boards are made on the basis of not damaging the original wall. (The edge holding strip and the skirting line play the role of connecting the wall and the floor; the upper wall liner or the upper wall pad (internal corner) is used for the triangular inner cushion between the wall and the corner of the floor. The advantage is that after the project is completed No rework) The yin and yang corners of the construction wall should be straight. The uneven corners will bring certain difficulty to the laying. Before laying, the uneven yin and yang corners must be treated, and the uneven corners must be Use hard triangular strips for filling and correction. After laying, it is best to install anti-collision corner protection to strengthen the external corners to improve the overall appearance. To

2. Measurement and cutting of the wall on the plastic floor

Measure on the spot, based on the principle of reducing waste, comprehensively considering the degree of aesthetics, and using ink fountains as long straight lines or marking guidelines. Cut the required size on demand to maximize economic benefits.

2. Operation points:

1. The cutting material must be handled by a dedicated person.

2. The damage caused during transportation and handling should be cut off with a trimmer before cutting.

3. When cutting the plastic floor, you must always pay attention to its directionality to avoid splicing during paving, which will affect the appearance. (For example, imitation marble, imitation wood grain, imitation carpet, imitation leather, imitation metal, imitation art effects, please pay attention to the original effect after cutting)

4. For each cutting, accurate data must be obtained at the construction site. The plastic floor has a certain degree of resilience, so the length of the upper wall contact surface is 1/2 of the plastic floor contacting the ground (the upper wall length is 10cm, and the ground should be set aside 20cm ), keep a margin of 2-3cm for each opening.

5. Wall corner (inside and outside corner) cutting plan:

Option 1: 45 degree angle bevel

(1) Use a 60-degree triangle to determine the angle and cut the plastic floor. You can't do everything to the end, you must leave a distance of 5-10 mm from the floor.

(2) Another piece of plastic floor on the upper wall is squeezed into the corner of the wall and folded in half to overlap the figure (1) above. Use a 45-degree triangle to determine the angle and cut out a 45-degree bevel.

(3) Two pieces of plastic floor on the wall are overlapped and cut with 45-degree slopes and then unfolded to obtain a 90-degree right angle.

Option 2: Triangular, V-shaped cutting

First cut out a triangular slice, and make a shallow groove on the center line of the back of the triangle to facilitate the bending of the plastic floor and the corner of the wall. You can't do everything to the end, you must start from the plane of the floor, leaving a distance of 5 mm. Cut off the excess plastic floor at a 45-degree angle on both sides of the external corner. Heat weld two 45-degree diagonal lines. (Do not cut the anchor board at the inner corner, and directly wrap the corner. On the back of the anchor board, at the intersection of the corresponding wall corner at the bottom, open a "V"-shaped groove about 2/3 deep of the material thickness.